| Wire length, processing on both sides min. | 700 mm |
|---|---|
| Wire length max. | 4000 mm |
| Strip length side 1 min. (processing set VoE 8-8, VoE 8-15) | 0.1 mm |
| Strip length side 1 max. (processing set VoE 8-8, VoE 8-15) | 18 mm |
| Strip length side 2 min. (processing set VoE 8-8, VoE 8-15) | 0.1 mm |
| Strip length side 2 max. (processing set VoE 8-8, VoE 8-15) | 28 mm |
| Wire cross section min. (processing set VoE 8-8) | 2 × 0.22 mm² |
| Wire cross section max. (processing set VoE 8-8) | 2 × 1.0 mm² |
| Wire cross section min. (processing set VoE 8-15) | 2 × 0.22 mm² |
| Wire cross section max. (processing set VoE 8-15) | 2 × 2.5 mm² |
| Open wire ends min. (with MQS 6.4 terminal, processing set VoE 8-8) | 40 mm |
| Open wire ends max. (with MQS 6.4 terminal, processing set VoE 8-8) | 99 mm |
| Open wire ends min. (with MQS 6.4 terminal, processing set VoE 8-15) | 50 mm |
| Open wire ends max. (with MQS 6.4 terminal, processing set VoE 8-15) | 99 mm |
| Lay length min. | 5 mm |
| Lay length max. | 80 mm |
| Lay length accuracy | Accuracy: ±10%, max. 4mm per pitch on average over 10pitches |
| Wire draw-in speed | 5 m/s |
| Wire length, optional | 700– 4000mm optional as of 150mm end length of twisted wires |
| Length accuracy | ± 0.1% + 1 mm |
| Seal diameter max. (Processing set for short open ends) | 5.5 mm |
| Seal length max. (Processing set for short open ends) | 11 mm |
| Noise level (without crimp modules) max. | 80 dB |
| Electrical connection | 3 × 208 – 480V, 50 – 60Hz, 10kVA |
| Wire protection/ground | 32 |
| Compressed-air connection | 5 – 8 bar |
| Air consumption (depending on configuration) min. | 5.5 m³/h |
| Air consumption (depending on configuration) max. | 13.2 m³/h |
| Network connection | Ethernet |
| Recommended operating pressure ±0.5bar/7.25psi | 6 bar |
| Operation outside the recommended operating pressure | Non-compliance with the recommended operating pressure can prevent peripheral devices from functioning completely correctly. Please also observe the technical data for peripheral devices. The maximum permitted operating pressure depends on the ambient temperature: 6.5 bar to 40 °C/6 bar at 40 °C and above |
| Weight (approx.) | 2000 kg |
| Length | 8463 mm |
| Width | 1780 mm |
| Height (with safety cover closed) | 1985 mm |
| Height (with safety cover open) | 2865 mm |
| Dimension Twister | 4 m |
| Minimum clearance around equipment for maintenance work | 1500 mm |
| Floor load capacity | 500 kg/m² |
| Floor conditions | Flat, stable, clean and vibration-free support surfaces. The support surface for machine load points must be a continuous base plate of concrete. No expansion joints between machine load points. Support surface non-slip. No plastic or asphalt coatings. |
| Ambient temperature min. | 10 °C |
| Ambient temperature max. | 45 °C |
| Humidity, non-condensing | 30 – 90 % |
| Processing outside the specifications | Processing outside the specifications upon request. In case of doubt, we will be happy to provide processing samples for your wires. |
| Producible parameters | Producible parameters depend on pitch, outer diameter, and end processing. Producibility can be verified using the producibility check software or with a feasibility test. |
Sigma 588
The Sigma 588 enables fully automated, high-performance production and output of twisted cables, including crimping, sealing, and intelligent wire shifting for any open end configuration.
The Sigma 588 is the first stage of fully automated twisted cable production with cross-sections from 0.22 mm² to 2.5 mm², tailored to meet the needs of various production volumes with high quality demands. It offers essential options such as crimping, sealing, and a full range of Quality Tools, including the intuitive Komax HMI user interface. The machine twists two individual wires into a UTP cable, a common requirement in the automotive industry. Its modular design allows for easy upgrades with additional crimp and seal modules which allows customization to meet specific customer needs. The machine”s intelligent, fully automatic wire position adjustment for open ends ensures highly efficient production with open end lengths ranging from 40 mm to 99 mm.
Tailored to production needs
With a 2+2 station configuration and all essential quality control tools, the Sigma 588 is ideally suited for high-volume production.
High process quality guaranteed
Automation minimizes operator influence and reduces human errors, while Q1250 algorithms control the production and ensure high quality results.
Intelligent adaptation to product specifications
The variable open end (VoE) processing set offers intelligent and integrated wire position adjustment for a wide range of open end configurations.
Versatile wire gauge range
The on-site changeable processing set of the Sigma 588 allows for both large wire gauges and smaller open end configurations.
Interested in the Sigma 588?
Talk to our team for pricing, availability and expert advice.
